Description
Shower flow Type Ⅱ on off cartridge 8-00-004-02(side in and bottom out) of shower valve is made by imported material which is non-toxic and free from incrustation. It adopts the physical attributes of magnet as driving force which realized zero leakage and more obvious water-saving capability.
Product Advantages
Long Life Cycle: We use magnet to turn valve on and off, there is much less friction so that the service life is more than 5-10 times the traditional valve. That is why we offer longer warranty than our competitors, you get 5 years warranty, anything broken in 5 years = brand new cartridge.
Leak Free: It uses the static sealing mode, while traditional mechanic valve use dynamic sealing. Magnetic valve uses the non-contact full sealing cylinder as the main body, which isolate the internal water flow from the external driving part.
Maintenance-Free: Our valve is made of PPS, one of the best anti-corrosion material. You only need to replace the valve spool when something happens. You will save great amount of maintenance costs.
Light Switch : No matter how high the water pressure is, children, the elderly or disabled can turn it on easily because magnet will help them turn on the valve.
Easy to install: With our instruction, young kids can assemble our product in less than 5 min.
Specification | DN15 | ||||
Use parameters | |||||
Maximum operating temperature | 90℃ | Opening pressure | ≤7N | ||
Switch trip | 5mm | Clamp nut torque | 3±0.5N.m | ||
Performance test | |||||
Strength test | Static pressure 2.5MPa | Average flow | ≥0.20L/s (0.1 Mpa) | ||
Pressure range | 0.05MPa-0.75MPa | Delay time | NO | ||
Seal test | High pressure | 0.75MPa | |||
Low pressure | 0.05MPa | ||||
Service life | 500,000 times | ||||
In & out term | Side in and bottom out | ||||
Main material | PPS、EPDM、NBR | ||||
Serial number | Item | Parameter | Description | Precautions |
1 |
Proper temperature | 4~90° | Cartridges can only be tested and used within this temperature range | Exceeding applicable temperature range may cause cartridge function failure |
2 | Thread locking torque |
2.5±0.5 N.m | Thread locking torque control is most suitable in the range of (2.5 ± 0.5) N.m | The tightening nut torque exceeds the specified range. Too small may cause water leakage and too large may damage the cartridge. |
3 |
Button stroke |
4.2mm |
button stroke 9mm | During the life test, the maximum stroke of the compression must be reserved from 0.2 to 0.4mm to avoid excessive force of the cylinder and long-term reciprocating operation, which may damage the cartridge parts. |
4 |
Pressing force |
≤7N | Maximum 7N force is required to open the cartridge | The pressing force of any test should not exceed 50N. Excessive force and long-term reciprocating operation may damage the cartridge parts. |
5 |
Pressure range |
0.05~0.75Mpa | The cartridge is within the pressure range of 0.05 ~ 0.75Mpa, various functions are normal, such as normal opening, closing without leakage, etc. | Do not exceed the pressure range to test the performance of the cartridge, otherwise the failure of over-high-pressure opening or over-low-pressure sealing and inadequate dripping may occur. |
6 |
Strength test |
2.5Mpa | The cartridge is installed in the valve body and in a closed state, it is slowly pressurized to 2.5Mpa at the water inlet, maintaining (60 ± 5) S. The cartridge could not appear the permanent deformation and rupture; 0.05 ~ 0.75Mpa), all functions of the cartridge are normal. |
For individual customers that exceed the strength test requirements of this standard, they need to repeat new testing and validation. |
7 |
Instantaneous flow |
≥0.2L/S (0.1Mpa) | When the water pressure is 0.1Mpa, press the button (0.5 ~ 1S) to open the cartridge, the instantaneous flow rate recorded is ≥0.2L/S .
| In order to ensure that the measured instantaneous flow rate is accurate, the diameter of the inlet pipe must be a pipe with a diameter of DN15mm or more. |
Why us?
We are the very 1st. manufacturer who applied magnetism into valve in domestic China.Our new magnetic water-saving valve is leak-free,non-friction,long-life cycle and easy to install.
Product Advantages
Long Life Cycle: We use magnet to turn valve on and off, there is much less friction so that the service life is more than 5-10 times the traditional valve. That is why we offer longer warranty than our competitors, you get 5 years warranty, anything broken in 5 years = brand new cartridge.
Leak Free: It uses the static sealing mode, while traditional mechanic valve use dynamic sealing. Magnetic valve uses the non-contact full sealing cylinder as the main body, which isolate the internal water flow from the external driving part.
Maintenance-Free: Our valve is made of PPS, one of the best anti-corrosion material. You only need to replace the valve spool when something happens. You will save great amount of maintenance costs.
Light Switch : No matter how high the water pressure is, children, the elderly or disabled can turn it on easily because magnet will help them turn on the valve.
Easy to install: With our instruction, young kids can assemble our product in less than 5 min.
Company Information
Huangshi Xingfa Technology Co.,Ltd. was established in 2013 with independent import and export rights and features the innovative cartridge and related valve&faucet creations.Our refined sanitary product designs are not only developed for individual consumers who are interested in adding quality and character to their homes, but also continue to be featured as the stylistic signature for a growing number of small and large scale architectural and interior design projects around the world.In addition to beautiful standard bathroom products, we also specialize in the development of extraordinary OEM and ODM Projects. Browse through our products sections on our website to see the variety of products available to find more about of the mesmerizing creations credited to us.
Assembly Line
Test Equipments
Our Showroom
Certification&Patents
We got nearly 30 national patents including invention patent,design patent and utility model patents.
Patents
Our Exhibition
Customers Visiting
Packing&Shipping
FAQ
Q:Are you trading company or manufacturer ?
A: We do not produce any products directly, but we have assemble production line.
Our cooperated factories produce all faucet accessories and then we combine them in our company. We have our own R&D team.
Q: Payment term?
A: T/T 30% in advance,70% balance before delivery
05, 25, 2021
05, 25, 2021
